How to Make a Weed Dabber

Jul 31, 2012 by SegraveMontonez679

The tool that I am going to inform you about is for using herbicides such as RoundUp. The largest blunders that people make when employing non-selective herbicides like RoundUp is overspray getting the herbicide on plants that they did not intend to spray, and more than applying the product. If you spray to the point of run off, you are applying way also a lot.

The weed dabber is a tool used for spot treating weeds without obtaining the herbicide on other plants.

Begin by going to your hardware retailer and purchasing a piece of 1- 1/two PVC pipe. You only need to have a piece 30 extended, but they might make you buy a 10′ section. It is fairly low cost even though. You’ll need a plastic PVC cap for a single finish of the pipe, and on the other end you are going to need an adapter to convert the PVC pipe to a common pipe thread. You are going to have to let the clerk at the hardware shop aid you locate the greatest mixture of fittings to use. What you require to do is to get the PVC pipe reduced down to a male garden hose kind fitting. Hardware retailers sell brass fittings that convert standard pipe thread to the same thread utilized on garden hoses.

Possibly what you will end up with is an adapter that will convert the 1-1/two PVC to 3/4 male pipe. Then an adapter to convert the three/4 male pipe to a male garden home fitting. They also make a cap that you can set up on the end of a garden hose, you will want one particular of those. This cap need to have a rubber garden hose washer in it so it seals correctly.

The PVC fittings have to be glued on so you’ll have to choose up some PVC pipe glue and cleaner. You have to use the cleaner to remove the film and gloss from the PVC pipe and fittings before you glue them. When you have them cleaned, just apply a coating of glue to both the pipe and the fitting, slide the fitting on and twist it at the identical time. Hold the fitting tight for 60 seconds and it will be glued tightly.

Cut a piece of pipe 30 lengthy and glue the pipe cap on one particular end, and the PVC to pipe thread adapter on the other finish. Apply a little quantity of pipe dope or Teflon tape to the threads of the adapter, and screw the male garden residence fitting onto the adapter. Screw the garden hose cap to the male garden hose fitting.

Now back to the end of the pipe that you glued the pipe cap to. Drill a really small hole appropriate in the middle of the pipe cap. You could have to experiment a little with the size of the hole you require, but make positive you start with a quite small hole. I’d begin with 1/16. Cut a piece of standard household sponge in a square about 1-1/two square. What you are going to do is location this sponge over the small hole you drilled in the pipe cap, and secure it there by covering it with a piece of lightweight screen or mesh cloth. Maybe even a piece of an onion bag. You can secure the mesh to the PVC pipe with a hose clamp, or electrical tape.

Remove the garden hose cap from the other finish of the PVC pipe, and fill the pipe with pre-mixed (prepared to use) RoundUp. Replace the garden hose cap and you have oneself a weed dabber. The RoundUp will seep out the hole in the finish of the pipe cap and be absorbed by the sponge. As extended as the garden hose cap is tight the vacuum in the pipe will maintain the herbicide from running out also fast. As soon as the sponge is damp, you can begin dabbing weeds. Don’t forget, you only want the weeds damp and not dripping wet. As extended as you are leaving some RoundUp on the weeds as you dab them, the herbicide must kill them.

Based on the temperatures, it could take a week or so before you can see the effects of the herbicide. If the sponge gets also dry you can loosen the cap a small to release the vacuum and more herbicide will be released onto the sponge. Or you can just turn the tool upside down and that really should let some air into the chamber, thus releasing the vacuum. As often, read the label and stick to the directions on the herbicide package.

For more information, please go to: 2005 accord exhaust system